Waterproofing Chemical

Product Details:

Product Description

Fosroc Conbextra GP2 Cement Precision  Grout is used for precision grouting where it is essential to withstand static and dynamic loads. Typical applications would be the grouting of base plates of turbines, compressors, boiler feed pumps etc., It can also be used for anchoring a wide range of fixings. These include masts,anchor bolts and fence posts.

Features:

• Store in Cool & Dry Place
• Covered Place

Additional Information:

• Item Code: 12093456
• Delivery Time: same day
• Packaging Details: bag

Product Details:

Product Specification Product Description

High performance Elastomeric coating for waterproofing external walls

Benefits

• No dilution required
• Excellent ability to bridge cracks
• Almost twice as thick as normal paints
• Resistant to algae and Fungus

Additional Information:

• Delivery Time: SAME DAY

Product Details:

Product Specification Product Description

Keeping the diverse requirements of customers in mind, we are instrumental in providing Dr. Fixit Pidicrete.

 Details:

• Waterproofing expert
• 301 PIDICRETE URP
• SBR latex for repairs and waterproofing
• Net weight: 1 kg
• Ref No: B17406
• MFD in: 04/2047
• MRP: 330.00
• Size: 1L/5L/20L

 Uses:

• Water probing

 Minimum QTY:

• 5 for 1L, rest 1

 Surface preparation:

• Mechanically clean the surface to remove all loose particles dirt oil grease etc. Vacuum clean to remove all loose material

 Recommended application:

 Economical waterproofing:

• Mix Dr fixit pidicrete URP with cement in ratio 1:15 by volume and apply in 2 coats
• Protective screed is a must

 

As repair mortar:

• Mix Dr fixit pidicrete URP at 10-15% by weight of cement in 1-3 cement fine sand mix for use as repair mortar along with 20% water by weight of cement to the workable consistency

 

As screed concrete:

• Mix Dr.fixit pidicrete URP 10-15% by weight of cement to a screed concrete of proportion 1:1.5:1.5(cement sand 6 mm aggregates) along with 20% water by weight of cement Mix the content to a uniform consistency

 

As bond coat in repair:

• Mix Dr pidicrete URP with cement in 1:1 ratio by volume and apply on a pre-wetted substrate over repair mortar when the bond coat is tacky

Product Details:

Uses

For spraying on freshly cast concrete, or newly exposed concrete surfaces after removal of form work, to form a temporary membrane which will retain suffi cient moisture for effective curing to take place. Used for concreting generally but especially useful for large areas of concrete such as pavements, runways and bridge decks; also for vertical or sloping surfaces as on towers, chimneys, canal linings, columns and beams, where water curing is diffi cult or unreliable. The curing compound is used for the curing of Dry Lean Concrete.

Single application : Forms moisture barrier

 No other curing necessary : Eliminates use of water, hessian or sand completely.

 Reliable : No risk of erratic or poor curing and ensures that cement hydrates efficiently.

 Ensures hard-wearing surface : Minimises risk of drying

shrinkage, cracks and dusty surfaces.

 Easy and safe spray application: Non-toxic and nonflammable.
Description :Concure WB is a white, low viscosity wax emulsion which incorporates a special alkali reactive emulsion breaking system. This system ensures that the emulsion breaks down to form a non penetrating continuous fi lm immediately upon contact with a cementitious surface. This impervious film prevents excessive water evaporation which in turn permits more effi cient cement hydration, thus reducing shrinkage and increasing durability.

Once formed, the membrane will remain on the concrete surface until eventually broken down and eroded by natural weathering. Where it is required to apply a further treatment to such concrete surface, it may be necessary to remove the membrane remaining after curing by wire brushing or other mechanical means.

The use of curing membranes on internal floor slabs is generally to be avoided where additional surface finishes are to be applied. Concure WB is however ideal where the concrete surface of a fl oor slab is to be left as ‘finished’.
Coverage rate

The recommended coverage rate is between 3.5 and 5.0 sq.m / litre ( 0.200 to 0.285 litres/sq.m). Coverage rates outside this recommended range may be used if necessary and suitable to meet specific requirements.

Application

Exposed concrete slabs : Concure WB should be spray applied on to the newly placed concrete slab as soon as possible after it is free from visible surface water, e.g. typically 1 to 2 hours after placing.

Shuttered and precast concrete : Concure WB curing agent should be spray applied to all surfaces as soon as formwork has been removed or the element demoulded.
In all cases the nozzle of the spray should be held approximately 450mm from the concrete surface and should be passed back and forth to ensure complete and even coverage. The pump pressure should be maintained at a level to produce a fine spray ensuring complete coverage of the surface.

Rate of application depends on requirements but is typically within the range of 200 to 285 ml/m2.

Additional Information:

• Item Code: 126754
• Delivery Time: immediate
• Packaging Details: drum

Product Details:

Bitumen.The bitumen grade 85/25 means the softening point is 85°c and penetration is 25 desi millimeter is produced in compliance and conformity with ASTM standard and meets the following specification.

Additional Information:

• Item Code: 342376
• Delivery Time: same day
• Packaging Details: drum ,bag

Product Details:

CHARACTERISTICS / ADVANTAGESAdhesion to most substrates (concrete, stone, brick,ferrous metals, glass, ceramic tiles)  Improves elasticity, flexibility and tensile strength ofcement and reduces cracking in mortar and concrete Economical, easy to use and non-toxicInhibits cracking, improves surface hardening, limitswear and dust production Makes the mortar waterproof and reduces susceptibilityto acids and greases, salt petre action, etc Mortar with SikaLatex SBR shows extremely goodbonding to bases like concrete, stone, brick etc Reduces viscosity of cement injection grout and improvesbond of cured injected materials with substrates SikaLatex SBR can be diluted with water (1 : 4 - 6)depending on the type of application Screed required with Sikacim / SikaPlastocrete Superto protect waterproofing layer Standard coating system can be further reinforced byplacing glass fibre reinforcement Sika Fabric-50 inbetween first and the second coat

Product Details:

Description:

• Reebaklens RR cleaning agent is a combination of acid based material, corrosion inhibitors and dispersing agents and is supplied as a clear green solution.

Additional Information:

• Technical data and guidance can be provided on a wide range of admixtures, concerting aids, grouts, repairs, Protective coatings and the Nitoflor range of industrial flooring systems which includes non metallic floor hardeners, epoxy floor coatings and self levelling floor toppings, epoxy heavy-duty abrasion resistant screed.
• Separate data sheets are available on these products

Uses:

• Reebaklens RR is used as a rust remover from steel bars prior to encasing in concrete / microconcrete.
• It can also be used on other steel surfaces prior to coating with epoxy systems.

Rapid action

• Safe with metals (except zinc and galvanised steel), wood, glass, plastic and rubber. No corrosive action.
• Penetrates oil and grease.

Technical Support:

• Fosroc provides a technical advisory service to specifies, end-users and contractors as well as on-site technical assistance in locations all over the country.

Properties:

• Specific gravity : 1.16 - 1.22 @ 25c
• For rusted metal (iron base)
• Apply Reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours.
• After 24 hours, a white layer will appear which will protect further corrosion of metal / steel for about 5-7 days.
• Before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth.

Removal of rust and mill scale:

• Prewet the floors, then using a stiff bristle broom, brush the affected areas with a solution of Reebaklens RR cleaning agent and water.
• Strength of the solution required will vary
• When the action has finished, wash down thoroughly with clean water.
• Wire brush again to remove remaining loose material and finish by thoroughly washing down with clean water.
• Repeat if necessary.
• High degree of rust or scale can be removed by soaking in the Reebaklens RR cleaning agent solution for 60 minutes.

Coverage:

• Approx. 2.0 - 2.5 m2/L
• Note coverage depends on the rusted area and the depth of deposition

Packaging:

• Reebaklens RR cleaning agent is available in 1, 5 and 20L containers

Shelf life:

• At least 1 year in original sealed containers under normal warehouse conditions.

Health & Safety instructions:

• Reebaklens RR cleaning agent is acid based and should be handled with care.
• It attacks zinc, aluminium and putty.
• If in doubt about its effect on a material, test a small area before application.
• Avoid contact with skin. Rubber gloves and goggles should be worn.
• Wash spillages with plenty of water.
• Enclosed areas should be well ventilated.
• If contact with eyes occur, wash immediately with water and seek medical advice

Additional Information:

• Delivery Time: 1
• Packaging Details: barrel

Product Details:

Product Details:

Sikadur 32 Lp Epoxy Bonding Agent

Sikadur®-32 LP is a solvent-free, two component bonding agent, based on selectedepoxy resins. Complies with ASTM C 881-78 type II, Grade 2 Class B+C

Additional Information:

• Delivery Time: 1

Product Details:

Product Specification Product DescriptionProduct Details :
Features :

• Renderoc RG is supplied as a ready to use blend of dry powders which requires only the site addition of clean water to produce a free-fl owing non-shrink repair micro concrete.
• The material is based on Portland cements, graded aggregates and fi llers, and additives which impart controlled expansion characteristics in the plastic state, while minimising water demand.
• The low water requirement ensures high early strength and long-term durability.
• For larger repairs, the mixed Renderoc RG may be modifi ed by the addition of 5mm to 12mm clean, graded, saturated surface dry aggregates at site.
• For exceptionally large repairs, the local Fosroc offi ce shall be consulted.

Advantages :

• Gaseous expansion system compensates for shrinkage and settlement in the plastic state.
• Can be pumped or poured into restricted locations.
• Highly fluid to allow for placement without vibration.
• Pre-packed to overcome site-batched variations.
• Rapid strength gain to facilitate early reinstatement.
• High ultimate strengths and low permeability of cured repair.
• Contains no chloride admixture.

Buy fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG online in India at wholesale rates. If you have been looking for fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG dealers, your search ends here as you can get the best fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG distributors in top cities such as Delhi NCR, Mumbai, Chennai, Bengaluru, Kolkata, Chennai, Pune, Jaipur, Hyderabad and Ahmedabad. You can purchase fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG of the finest quality and rest assured to get the best in terms of both durability and performance. If you are bothered about the fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG prices, you can be totally sure to get the best rates as brings you genuine fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG rates and quality assured products only from the best of brands with exclusive brand discounts you wont find anywhere else. Procure fosroc 25 kg Non-Shrink Cementitious Micro Concrete Renderoc RG today and avail the best offers on your purchase

Additional Information:

• Item Code: 22567789
• Delivery Time: same day
• Packaging Details: bag

Product Details:

part from EPDM, Polygomma can manufacture Butyl Roofing Membranes is manufactured using high-grade synthetic rubber compounds. Our experience of over 50 years in the rubber industry helps us to manufacture high-quality roofing and waterproofing membranes.
Our entire manufacturing process does not produce any liquid or gaseous waste. Also at the end of the service life of the membrane, it can be recycled and reused for other applications. This makes the membrane environmental friendly.

Additional Information:

• Item Code: 1232456
• Delivery Time: SAME DAY
• Packaging Details: ROLL

Product Details:

Product Specification Product DescriptionWe are leading seller of Concrete Admixtures of brands like Fosroc, Sika and Dr. Fixit - Pidilit

Additional Information:

• Item Code: 124323
• Delivery Time: same day
• Packaging Details: drum

Product Details:

high performence  waterproof coating for all types of plasters & concrerte wall & roof 

Product Details:

Product Description

Tar Sheet which is manufactured with fine-grade raw material. It is highly reliable for longer service life and offers extreme resistance to dust, water and sunlight. Owing to these features, it is highly demanded in the market as well as acclaimed by the patrons. We are offering this product at affordable price and ensure timely delivery at the clients' premises.

 Salient features

- Corrosion resistance

- Glossy shine

- Durable

- Temperature resistance

Additional Information:

• Delivery Time: same day

Product Details:

Additional Information:

• Delivery Time: same day
• Packaging Details: roll

Product Details:

Our company is well known in the industry for the manufacture and the export of a high quality of Bituminous Primer which are high on demand and they are used on the surfaces which require water proofing. 

Additional Information:

• Delivery Time: SAME SAY
• Packaging Details: 20 KG DRUM

Product Details:

Product DescriptionPlacing of concrete and improving its strength can be easily enhanced through using the High Strength Admixtures without changing the ratio of cement and water in the plain mixture. Main ingredients which are used in superplasticizers are completely based on the SMF (sulfonated melamine formaldehyde condensate) SNF (naphthalene formaldehyde condensate). The effect of superplasticizer does not depend on the amount of addition whereas concrete mixes with slump level with SNF or SMF based admixtures. It is responsible for dispersion of cement particles, the large one to the smaller particles; it gives a remarkable increase in the fluidity of cement when it gets mixed.
Additional Information

Additional Information:

• Delivery Time: same day
• Packaging Details: drum